Air Intake & Fuel Line Magnetic Enhancement


Back to Home


The magnetic enhancer attached to a fuel hose

Magnetic Enhancement

This is the newest addition to the products we offer. We are using 20mm diameter by 10mm thick neodymium magnets, with a pulling power of about 6 kg or 13.5 pounds each. The mounting system is simple and basic - it's a plate of steel. It's not pretty, and you will notice that the bottom of the magnet is exposed. This is on purpose. It increases the available amount of magnetic force directly transmitted to the object that you want to have an effect on. If we were to cover it with a layer of plastic, as is the usual procedure, we would reduce effectiveness by somewhere around 20%. The magnets hold on to the steel strip with a pulling power in combination of 27 pounds. Their polarity can be changed, and they can be moved around; we sell it with opposite poles up, because we have found in tests that the best fuel efficiency increases occur when fuel passes through opposing magnetic poles in sucession, on a horizontal plane rather than on opposite sides - just as we have them here. The fact that there are two magnets also offers an interaction between the poles that would not be present if there were only one magnet with opposing poles on the same side.

And the price? Its $29.50. This is very inexpensive for this kind of application. The cases of the competition are prettier, and the prices sometimes double, or more - in any case, significantly more expensive, with no added effectiveness. This is probably the cheapest, but most effective for the price, magnetic fuel enhancement that you will find available for sale on the internet anywhere.

The purpose of the case is simply a means of securing the magnet against whatever it is bound. It does that quite well - and the securing tie can be easily released and it can be remounted.

They can be used on fuel hoses, on the inlet and outlet of the vapor expansion tubes we sell, on boiler gas inlets, on water pipes - anywhere where an increase in combustion efficiency is sought, or the benefits of ionization are required. There are too many applications for this to be quoted here. For maximum efficiency - and this is always recommended - you should mount two near each other. So one is north pole, and one is south pole, on the facing side next to the tube/pipe/etc. that you are mounting it on. Doesn't matter what order this is in - whether north/south or south/north. At these prices, buying two is not expensive. If you buy only one - as is the case with many magnetic improvement devices - you will halve the efficiency. Single pole treatment is limited, if it does anything.

Because of the mounting, the magnets are held in place by their attraction to the metal bits. The attachment wraps are reusuable - that is, if you wrap it around something, and want to move or remove it, its easy enough to detach it. The reason we have them mounted as they are, so you can pull the magnets, with some effort, from their mounting, is so that you can reverse the polarity without having to purchase another magnet.

The only disadvantage of not having a protective bottom is if it is used on hot surfaces. We don't recommend you using this on anything that is itself near the boiling point of water. The great majority of applications will not be anywhere near this. One thing to remember - don't put the magnets together! If you do, they will have 26 pounds of pulling power between them to separate, so you could pinch your skin painfully if it was caught between the two. In that case, you would have to use a screwdriver to pry them apart - ouch!

What sort of improvements or fuel efficiency savings can you expect? With 2 of them - one on them on the fuel hose next to each other, as in the picture, and one on the inlet outlet of our expansive tube - we were able to go from 45mpg on our standard intake manifold vaporizer system to 51mpg. The car before we started doing anything got 30mpg. The improvement over the base mpg was a 20% increase! We have obtained this improvement over and over again - this is not a one off example. The mode, rather than the average, is around 15%.

You could just purchase 2 of these - 1 for the fuel line, and 1 on your air intake - without getting anything else, and expect somewhere in the range of 12-15% increase in mpg. You could do this on any vehicle, without an EFIE or lambda sensor simulator - and it would work. And take about 5 minutes to install. The increase to 20% is achievable with our expansion tube in a vaporizer arrangement, because the inlet and outlet constrict all the gases entering and leaving the expansion tube so they are exposed to the strong magnetic fields from the magnets.

As with all our products, if after ordering and trying these magnetic enhancers you are not pleased with the results, after returning them to us we will give you a full refund. This guarantee is for one year from date of purchase. This does not affect your statutory rights.